Kinco Low Voltage Servo FD122-AA-000, FD122-LA-000
Kitoma Indonesia : Kinco Low Voltage Servo FD122-AA-000, FD122-LA-000
FD122-AA-000 Small Inertia DC60V
FD122-AA-000 : CANopen communication protocol
FD122-LA-000 : Modbus 485 communication protocol
FD122-AA-00 Servo Motor Applicable
SMH40S-0005-30AAK-4DKH : Cable connector
SMH40S-0005-30ABK-4DKH : Cable connector and brake
SMH40S-0010-30AAK-4DKH : Cable connector
SMH40S-0010-30ABK-4DKH : Cable connector and brake
SME60S-0020-30AAK-3DKH : Cable connector
57S-0010-10AAK-FDFH : Cable connector
57S-0015-08AAK-FDFH : Cable connector
85S-0020-05AAK-FLFN : HFO standard connector
Kinco FD122 Fetaures
- Support CANopen communication protocol
- Input voltage range from DC24V to 70V
- Rated current is 6A
- Peak current is 15A
| Main supply voltage | 24VDC～70VDC |
| Control circuit voltage | DC24V 1A（Optional） |
| Rated current(RMS) | 6A |
| Peak current(PEAK) | 15A |
| Feedback signal | 2500PPR (incremental encoder with 5V supply) |
| Brake chopper | Use an external braking resistor according to application, mainly in high speed start and stop application |
| Brake chopper threshold | DC79V ± 2V |
| Over-voltage alarming threshold | DC86V ± 2V |
| Under-voltage alarming threshold | 18V± 2V |
| Cooling method | Natural air cooling |
| Weight | 0.565 Kg |
| Input specification | 4 digital inputs, with COMI terminal for PNP (high level valid 12.5-30V) or NPN (low level valid) connection |
| Input function | Define freely according to requirement, supporting following functions: Driver enable, driver fault reset, driver mode control, proportional control, positive limit, negative limit, homing signal, reverse command, internal speed section control, internal positive section control, quick stop, start homing, active command, switch electronic gear ratio, switch gain |
| Output specification | 3 digital outputs, OUT1-OUT2 current is 100mA, BR+/BR- (Brake control output ) current is 500mA, can drive brake device directly |
| Output function | Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, N signal, maximum speed obtained in torque mode, motor brake, position limiting, reference found, multi-position reached |
| Encoder Signal Output | Output the encoder signal of motor, Used in multiple axis synchronous control, supports 2M at most |
| RS232 | RS232, Connections with PC (2-2, 3-3, 5-5) or controller |
| Protection Functions | Over-voltage protection, under-voltage protection, motor over-heat protection(I²T), short-circuit protection, drive over-heat protection, etc |
| CAN BUS | Supports 1M baud rate, communicates with controller via CANopen protocol |
| Operating temperature | 0～40℃ |
| Storage temperature | -10℃～70℃ |
| Humidity(non-condensing) | Below 90%RH |
| Protection class | IP20 |
| Installation environment | Installed in a dust-free, dry and lockable environment(such as in a electrical cabinet) |
| Installation mode | Vertical installation |
| Altitude | No power limitation below 1000m |
| Atmospheric pressure | 86kpa～106kpa |
Mechanical Dimension Diagram
Untuk informasi lebih lanjut silakan hubungi bagian Marketing kami, kami senang untuk membantu :
| Hubungi | : Sales & Marketing |
| Alamat |
: Simprug Plaza |
|
Jl. Simprug Raya Blok B.2 No.5 Cikarang Baru Jababeka II - Bekasi 17530 Jawa Barat - Indonesia |
|
| Telepon |
: 021 2851 8059 |
| Mobile | : 0857 7664 0198 (Sales & Marketing) |
| Fax | : 021 2851 8058 |
| : sales@kitomaindonesia.com | marketing@kitomaindonesia.com | scales@kitomaindonesia.com | kitomascale@gmail.com |
