Kinco Servo FD622S-LA-000, FD622S-AA-000
Kitoma Indonesia : Kinco Servo FD622S-LA-000, FD622S-AA-000
Features
- CANopen communication
- Main Supply Voltage : AC220V ± 15% 47-63Hz
- Rated Output Power (kW) : 0.2 - 2.3kW
Type Servo AC
Current : Min 4A, Max 25A
Output signal : CANopen
Output power : Min 0.2kW (0.27HP), Max 2.3kW (3.08HP)
Voltage : 380 VDC
FD622SS suitable for servo motors
- SMH110D-0126-30AAK-4HKC : YL22 standard connector
- SMH110D-0126-30ABK-4HKC : YL24 standard connector and brake
- SMH110D-0126-30AAk-4HKD : Intercontec connector
- SMH110D-0126-30ABK-4HKD : Intercontec connector with brake
- SMH110D-0157-30AAK-4HKC : YL22 standard connector
- SMH110D-0157-30ABK-4HKC : YL24 standard connector and brake
- SMH110D-0157-30AAK-4HKD : Intercontec connector
- SMH110D-0157-30ABK-4HKD : Intercontec connector with brake
- SMH110D-0188-30AAK-4HKC : YL22 standard connector
- SMH110D-0188-30ABK-4HKC : YL24 standard connctor and brake
- SMH110D-0188-30AAK-4HKD : Intercontec connector
- SMH110D-0188-30ABK-4HKD : Intercontec connector with brake
- SMH130D-0157-20AAK-4HKC : YL24 standard connector
- SMH130D-0157-20ABK-4HKC : YL24 standard connector and brake
| Main supply voltage | 3-phase AC380V -20/+15% 47~63Hz |
| Control circuit voltage | 18VDC~30VDC 1A |
| Rated current(RMS) | 7A |
| Peak current(PEAK) | 25A |
| Feedback signal | 2500PPR (incremental encoder with 5V supply) |
| Brake chopper | Use an external braking resistor according to application, mainly in occasion of quick stop |
| Brake chopper threshold | DC680V±5V |
| Over-voltage alarming threshold | DC700V±5V |
| Under-voltage alarming threshold | DC400V±5V |
| Cooling method | Fan |
| Weight(Kg) | 2.4 |
| Digital input specification | 7 digital inputs, with COMI terminal for PNP (high level valid 12.5-30V) or NPN (low level valid) connection. |
| Digital input function | Define freely according to requirement, supporting following functions: Driver enable,driver fault reset,driver mode control, proportional control, positive limit, negetive limit, homing signal,reverse command, internal speed section control, internal positive section control, quick stop, start homing, active command, switch electronic gear ratio, switch gain |
| Digital output specification | 5 digital outputs,OUT1～OUT4 current is 100mA, BR+/BR- (Brake control ourtput ) current is 500mA, can drive brake device directly |
| Digital output function | Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, Z signal, maximum speed obtained in torque mode, motor brake, position limiting, reference found, multi-position reached. |
| Analog input | 2 analog input, can be used to control speed and torque, the input range is -10V~10V.Output encoder signal is optional, can be used in the multiple axises synchronization, the max. |
| Encoder signal output function | Output encoder signal is optional, can be used in the multiple axises synchronization, the max. output frequency is 2MHz |
| RS232 | The max. baudrate is 115.2KHz, use JD-PC software to communicate with PC, or via free protocol to communicate with controller. |
| Protection functions | Over-voltage protection,under-voltage protection,motor over-heat protection(IT),short-circuit protection,drive over-heat protection,etc. |
| RS485 | The max. baudrate is 115.2KHz, use Modbus RTU protocol to communicate with controller. |
| CAN BUS | The max. baudrate is 1MHz, use CANopen protocol to communicate with controller. |
| Operating temperature | 0~40℃ |
| Storage temperature | -10℃~70℃ |
| Humidity(non-condensing) | Below 90%RH |
| Protection class | IP20 |
| Installation environment | Installed in a dust-free,dry and lockable environment(such as in a electrical cabinet) |
| Installation mode | Vertical installation |
| Height | No power limitation below 1000m |
| Atmospheric pressure | 86kpa~106kpa |
Mechanical Dimension Diagram
Untuk informasi lebih lanjut silakan hubungi bagian Marketing kami, kami senang untuk membantu :
| Hubungi | : Sales & Marketing |
| Alamat |
: Simprug Plaza |
|
Jl. Simprug Raya Blok B.2 No.5 Cikarang Baru Jababeka II - Bekasi 17530 Jawa Barat - Indonesia |
|
| Telepon |
: 021 2851 8059 |
| Mobile | : 0857 7664 0198 (Sales & Marketing) |
| Fax | : 021 2851 8058 |
| : sales@kitomaindonesia.com | marketing@kitomaindonesia.com | scales@kitomaindonesia.com | kitomascale@gmail.com |
