CD422S-AA-000 Kinco AC Servo Drive CD422S-AF-000
Kitoma Indonesia : CD422S-AA-000 Kinco AC Servo Drive CD422S-AF-000
CD422S Features
- Main Supply Voltage : AC220V ±20% 47~63Hz
- Rated Output Power : 0.2~0.75 kW
- Dimension : 166 x 141 x 61 mm
CD422S Suitable for servo motors
SMH60S-0020-30AAK-3LKH : Cable connector
SMH60S-0020-30ABK-3LKH : Cable connector and brake
SMH60S-0020-30AAK-3LKN : HFO standard connector
SMH60S-0020-30AAK-3LKM : Intercontec connector
SMH60S-0020-30ABK-3LKM : Intercontec connector with brake
SMH60S-0040-30AAK-3LKH : Cable connector
SMH60S-0040-30ABK-3LKH : Cable connector and brake
SMH60S-0040-30AAK-3LKN : HFO standard connector
SMH60S-0040-30AAK-3LKM : Intercontec connector
SMH60S-0040-30ABK-3LKM : Intercontec connector with brake
SMH80S-0075-30AAK-3LKH : Cable connector
SMH80S-0075-30ABK-3LKH : Cable connector and brake
SMH80S-0075-30AAK-3LKN : HFO standard connector
SMH80S-0075-30AAK-3LKM : Intercontec connector
SMH80S-0075-30ABK-3LKM : Intercontec connector with brake
SME60S-0020-30AAK-3LKH : Cable connector
SME60S-0020-30ABK-3LKH : Cable connector and brake
SME60S-0020-30AAK-3LKN : HFO standard connector
SME60S-0040-30AAK-3LKH : Cable connector
SME60S-0040-30ABK-3LKH : Cable connector and brake
SME60S-0040-30AAK-3LKN : HFO standard connector
SME80S-0075-30AAK-3LKN : Cable connector
SME80S-0075-30ABK-3LKH : Cable connector and brake
SME80S-0075-30AAK-3LKN : HFO standard connector
Technical Specifications
| Main supply voltage | Single-phase AC220V -20/+15% 47~63Hz |
| Control circuit voltage | 18VDC~30VDC 1A |
| Max. continuous current | 4A |
| Peak current(PEAK) | 15A |
| Feedback signal | 2500PPR (incremental encoder with 5V |
| Brake chopper | Use an external braking resistor according to application, mainly in occasion of quick stop |
| Brake chopper threshold | DC380V±5V |
| Over-voltage alarming threshold | DC400V±5V |
| Under-voltage alarming thresholdDC200V±5 | |
| Cooling method | Natural air cooling |
| Weight | 1.2kg |
Position Mode
| Max. frequency of input pulse | Differential signal: 500KPPS, Open-collector signal: 200KPPS |
| Pulse command mode | Pulse+direction, CCW+CW, (5V, if the input is 24V, the 2K resistor is needed) (do not support A+B phase) |
| Command smoothing | Low-pass filtering(Adjustable by internal parameter setting) |
| Feedforward gain | Adjustable by internal parameter setting |
| Electronic gear ratio | Setting range, Gear factor: -32768~32767, Gear divider: 1~32767, 1/50≤ |
| Position loop sampling frequency | 1KHz |
Speed Mode
| Analog input voltage range | -10V~+10V(Resolution 12bit) |
| Input impedance | 200K |
| Analog input sampling frequency | 4KHz |
| Command source | External analog command / internal command |
| Command smoothing | Low-pass filtering(Adjustable by internal parameter setting) |
| Input voltage dead-zone setting | Adjustable by internal parameter setting |
| Input voltage offset settiong | Adjustable by internal parameter setting |
| Speed limit | Adjustable by internal parameter setting |
| Torque limit | Adjustable by internal parameter setting / External analog command control |
| Speed loop sampling frequency | 4KHz |
Torque Mode
| Analog voltage input range | -10V~+10V(Resolution 12bit) |
| Input impedance | 200K |
| Input sampling frequency | 4KHz |
| Command source | External analog command / internal command |
| Command smoothing | Low-pass filtering(Adjustable by internal parameter setting) |
| Speed limit | Adjustable by internal parameter setting / External analog command control |
| Input voltage dead-zone setting | Adjustable by internal parameter setting |
| Input voltage offset setting | Adjustable by internal parameter setting |
| Current sampling frequency | 16KHz |
Digital Input & Output
| Input specification | 7 digital inputs, with COMI terminal for PNP (high level valid 12.5-30V) or NPN (low level valid) connection |
| Input function | Define freely according to requirement, supporting following functions: Driver enable,driver fault reset,driver mode control, proportional control, positive limit, negetive limit, homing signal,reverse command, internal speed section control, internal positive section control, quick stop, start homing, active command, switch electronic gear ratio, switch gain |
| Output specification | 5 digital outputs,OUT1~OUT4 current is 100mA,OUT5 current is 800mA, can drive brake device directly |
| Output function | Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, Z signal, maximum speed obtained in torque mode, motor brake, position limiting, reference found, multi-position reached |
Operation Environment
| Protection functions | Over-voltage protection,under-voltage protection,motor over-heat protection(I2T),short-circuit protection,drive over-heat protection,etc. |
| Communication interface | RS232 (Connections with PC: 2-5, 3-1, 5-6) |
| Operating temperature | 0~40℃ |
| Storage temperature | -10℃~70℃ |
| Humidity(non-condensing) | Below 90%RH |
| Protection class | IP20 |
| Installation environment | Installed in a dust-free,dry and lockable environment(such as in a electrical cabinet) |
| Installation mode | Vertical installation |
| Altitude | No power limitation below 1000m |
| Atmospheric pressure | 86kpa~106kpa |
Mechanical Dimension Diagram
Untuk informasi lebih lanjut silakan hubungi bagian Marketing kami, kami senang untuk membantu :
| Hubungi | : Sales & Marketing |
| Alamat |
: Simprug Plaza |
|
Jl. Simprug Raya Blok B.2 No.5 Cikarang Baru Jababeka II - Bekasi 17530 Jawa Barat - Indonesia |
|
| Telepon |
: 021 2851 8059 |
| Mobile | : 0857 7664 0198 (Sales & Marketing) |
| Fax | : 021 2851 8058 |
| : sales@kitomaindonesia.com | marketing@kitomaindonesia.com | scales@kitomaindonesia.com | kitomascale@gmail.com |
